top of page

Cushion-Cut Lab-Grown Diamonds: Square and Elongated Shapes, Proportions, Four Cut Styles and Grading Reports

1 day ago
11 min read
Angled cushion diamond and labelled side profile.

Figure 1. An angled view shows the curved sides and rounded corners. The profile shows the table, crown, girdle, pavilion and culet.


A cushion-cut lab-grown diamond can look like a softly rounded square or a longer rectangle with gently bowed sides. Two 2-carat stones graded as Cushion Modified Brilliant can look quite different. One can appear wide and throw broad flashes, while the other looks slender with fine scintillation. The outline, millimetre dimensions, facet arrangement and light performance explain those differences.


Start face-up with the sides and corners, then compare measurements. Read the grading report for proportions and cutting style. Finally, tilt the loose diamond to see how the centre, ends and corners light up.


What gives a cushion cut its distinctive look?


A cushion keeps the structure of a square or rectangle while allowing the cutter to soften the sides and corners. A near-square stone can provide more coverage across the finger. An elongated stone set north–south emphasises length, while an east–west setting emphasises width across the hand. A four-prong solitaire lets you see the shape between the prongs.


The profile matters too. A higher crown can make the table, crown facets and girdle more distinct from an angle, and some designs produce broad flashes or strong fire. Lower crowns can also look lively face-up. If much of the depth sits in the pavilion or girdle, the diamond may face up smaller for its weight or require a taller setting. The whole facet arrangement determines how the diamond responds to light.


Four cushion outlines at the same length-to-width ratio


Look along each side and see whether its middle is nearly straight or bows out. Then check how tightly the long and short sides meet at each corner. Even an angular cushion usually has a small curve or clipped transition at the corner, unlike the pointed corner of a princess cut.


Four face-up cushion outlines with different side and corner curves.

Figure 2. From left: straight sides with tighter corners, straight sides with broad corners, curved sides with tighter corners, and curved sides with broad corners. Illustrative.


Outline

What to look for

Face-up effect

Straight sides, tighter corners

Nearly straight sides with a short corner curve.

Crisp, squarish outline.

Straight sides, broad corners

Straight midsections with more gradual corners.

Square structure with softened corners.

Curved sides, tighter corners

The sides bow out, then turn sharply into each corner.

Full middle and distinct corners.

Curved sides, broad corners

The bowed sides flow into long corner curves.

Strong pillow outline. Elongated examples may look almost oval.


A cushion may have straighter long sides and rounder ends. Rotate a square cushion’s face-up image by 90° to check its outline. On an elongated cushion, check whether the right and left sides match and whether the two ends have similar curves. For studs, equal measurements can still look different if one diamond has tighter corners than the other.


Choosing a length-to-width ratio for square and elongated cushions


Divide the reported length by the width. In its Square Cushion Modified Brilliant guideline, IGI treats 1.00–1.05 as square and 1.06 and above as rectangular. The finer divisions below describe how elongated a stone looks. Edge curvature and rounded corners can influence that impression near any boundary.


Five illustrated cushions with approximate length-to-width ratios of 1.00, 1.10, 1.30, 1.50 and 1.70.

Figure 3. Face-up cushion silhouettes from near-square to elongated, with approximate ratios.


Six cushion outlines at constant width, with ratios of 1.00, 1.05, 1.15, 1.25, 1.35 and 1.40.

Figure 4. Cushion outlines drawn to scale at a constant width.


Ratio

Appearance

What to check

1.00–1.05

Square or near-square

Balanced proportions and good width.

1.06–1.14

Slightly elongated

Straight edges can make elongation more obvious.

1.15–1.24

Moderately elongated

Clear length with a full outline.

1.25–1.35

Distinctly elongated

Check width, end curves and persistent central darkness.

1.36 and above

Very elongated

Compare light return at both ends and setting orientation.


At a width of 6.50 mm, ratios of 1.05 and 1.15 give lengths of about 6.83 and 7.48 mm. That is a difference of 0.65 mm. A ratio of 1.25–1.35 gives a more pronounced north–south silhouette. Decide how much width you want to retain before comparing length. IGI fancy-shape cut guidelines


Why can one 2-carat cushion look larger than another?


All are 2.00 ct. Length, width and depth in millimetres: A near-square, 7.15 × 7.00 × 4.60, ratio 1.02. B elongated, 8.00 × 6.30 × 4.42, ratio 1.27. C smaller face-up, 6.85 × 6.70 × 4.95, ratio 1.02.

Figure 5. Three 2.00-carat examples. The face-up outlines are drawn to the same scale.


B is 0.85 mm longer and 0.70 mm narrower than A. A covers more across the finger, while B extends farther along it. C has almost the same ratio as A, but is smaller in both face-up dimensions and deeper in profile. Use the actual report measurements and face-up view when assessing a stone.


How to read the proportions of a modern cushion


For an initial search among colourless and near-colourless modern brilliant or modified brilliant cushions, try a 55–65% table and 60–70% total depth. The narrower IGI guideline below applies to the Square Cushion Modified Brilliant. For elongated stones, decide on a minimum face-up width and compare light at both ends, the girdle and the rest of the profile. Compare step cuts, mixed cuts and coloured diamonds within their own groups.


Parameter

IGI square modified brilliant

How to use it

Length-to-width ratio

1.00–1.05

Divide length by width. Check sides and corners as well.

Table

55%–62%

Compare the top facet with crown height and central brightness.

Total depth

62%–68%

Use actual millimetres for face-up comparison and setting clearance.

Crown height

8%–16%

Check how the crown rises above the girdle and whether the sides look balanced.

Pavilion depth

40%–56%

Check culet position and light return when tilted.

Girdle percentage

2.0%–5.1%

Check overall thickness. Ask for a scan or profile if only a verbal range is shown.

Girdle thickness

Thin to Slightly Thick

Locate the thinnest and thickest spots, especially at corners and prong positions.

Culet

Pointed, None, Very Small or Small

See whether it is visible face-up and check clearance below.

Symmetry

Very Good or Excellent

Compare precision of outline and facets. Inspect optical patterns separately.

Polish

Very Good or Excellent

Read surface finish separately from cut and symmetry.


IGI calls for final visual confirmation. Its square-cushion table gives no corresponding full ranges for elongated cushions and lists no universal crown or pavilion angles for cushions. If you have a 3D scan, compare the inclinations of corresponding side and corner facets alongside crown and pavilion plots and video. IGI fancy-shape cut guidelines, page 10 · Modern cushion proportion examples


Two profiles with the same width and total depth but different crown and pavilion depths.

Figure 6. At the same total depth, the left profile has a higher crown and a smaller table, while the right profile has a deeper pavilion. Illustrative.


When should a stone outside the initial range stay on the shortlist?


Two elongated cushions may both be 70% deep. At 6.30 mm across, one is about 4.41 mm deep. At 7.00 mm across, the other is about 4.90 mm deep. That difference matters in a low setting. Keep a deeper stone in contention if it has the face-up dimensions you want and responds well under light at different angles. If it faces up small and has a thick girdle or deep pavilion, examine what that profile contributes to the look.


Read table percentage from the report. To check total-depth percentage, divide depth in millimetres by width where that is the laboratory’s convention. With an elongated cushion, a narrower width raises the percentage at the same depth.


Four cutting styles and how their light patterns compare


A cushion has an outline, a facet arrangement and a face-up light pattern. A report’s Shape and Cutting Style entry describes the first two. Broad flashes, crushed ice and combinations of the two describe what you see. An elongated Cushion Modified Brilliant can have broad flashes in the centre and finer flashes at its edges.


Report description

Facet structure and what to check

Cushion Brilliant

Radiating brilliant facets. Compare flash size and distribution in video.

Cushion Modified Brilliant

Modified brilliant facet arrangement. Can produce broad, fine or combined light patterns.

Cushion Step Cut

Facets arranged in steps. Look for broad bands of light and persistent dark areas.

Cushion Mixed Cut

Combines facet styles. Use the face-up video and available facet plots to identify the result.


Crown and pavilion views of brilliant, modified brilliant, step and mixed cuts.

Figure 7. Crown above, pavilion below. Brilliant and step-cut plots come from the sample reports. The modified brilliant comes from IGI’s guideline. The mixed cut is schematic.


The brilliant sample has radiating pavilion facets. The modified brilliant example divides its radiating facets differently. The step cut uses successive rows of facets that follow the outline. The mixed-cut illustration combines a step-cut crown with a radiating pavilion, one of several possible combinations. Use diagrams for facet structure and video for the size and timing of flashes. GIA definitions of cutting styles


Two cushion diamonds with broad and fine flash patterns.

Figure 8. Broad flashes on the left and fine, crushed-ice-like scintillation on the right. Illustrative.


Visible pattern

What to look for in motion

How it relates to the report

Broad flashes

Large bright areas alternate across the centre and corners.

Possible in some brilliant and modified brilliant designs.

Crushed-ice scintillation

Small flashes are dense and distributed across the face.

Common in some modified brilliants. Check the stone.

Broad centre, fine edges

Larger central flashes alternate with finer flashes around the perimeter.

A visual description. Mixed Cut is a separate report term.

Radiating star pattern

Distinct light and dark rays extend from the centre.

Possible in several structures. Confirm hearts and arrows with a reflector.

Step-like bands

Strips of light open and close as the stone turns.

Look for a step-cut structure or partial step faceting.


Reflections can create visible bright and dark areas smaller than the physical facets. With a fine pattern, check whether the centre and perimeter both respond. A persistent grey centre can be visible surrounded by active edges. Antique-style old mine cushions are a less common variation, often with a higher crown, smaller table and visible culet. GIA research on virtual facets


What to check on an actual grading report


Four report excerpts showing report numbers, cutting styles, measurements and grades.

Figure 9. Four public IGI excerpts. Clockwise from top left: brilliant, modified brilliant, mixed cut and step cut. Original reports are linked below.


Public IGI report

Length × width × depth (mm)

Ratio

Table / depth

12.48 × 8.91 × 5.80

1.40

59% / 65.1%

5.59 × 5.58 × 3.89

1.00

65% / 69.7%

11.08 × 9.06 × 4.92

1.22

75% / 54.3%

9.42 × 6.25 × 4.70

1.51

70% / 75.2%


Find Shape and Cutting Style and Measurements before moving to the proportion diagram and grades. In the top-right report, the cut grade is Very Good and both polish and symmetry are Excellent. The sample is a fancy pink diamond, so its proportions should be understood in the context of coloured-diamond cutting. Match the report number to the girdle inscription, then verify the measurements and video.


Two IGI reports both say Cushion Brilliant. One measures 12.48 × 8.91 × 5.80 mm, with a 65.1% total depth and a ratio of about 1.40. The other measures 6.99 × 5.56 × 3.99 mm, with a 71.8% total depth and a ratio of about 1.26. The same cutting-style name covers different proportions. Compare video to assess brightness. First IGI report · Second IGI report


Read cut, polish and symmetry as separate grades. IGI can grade the cut of fancy shapes. Since October 2025, GIA has used Premium or Standard overall quality assessments for eligible colourless to near-colourless lab-grown diamonds. Check the laboratory, date and report type. RAGAZZA’s DAII™ is for comparing round diamonds. We assess cushions individually by outline, proportions, facets and video. IGI cut grading · GIA lab-grown diamond services


Can cushions show hearts and arrows?


Some designs can show eight arrows through a reflector with the crown facing the viewer, and eight hearts with the pavilion facing the viewer. Request both images of the same loose diamond, with the report number. Regular video can show arrow-like reflections. Use the reflector images to check completeness and compare corresponding corner and side directions. Re-centre the stone if either image is off axis. IGI hearts and arrows · Example of a cushion hearts-and-arrows design


Using video to assess brightness, fire and dark areas


Compare stones against the same background, exposure and magnification. Pause face-up, then tilt each stone a few degrees along both axes. Watch the centre, ends and corners. White return shows brightness, coloured flashes show fire, and changes in light and dark show scintillation.


• Start in soft, even light. Check the centre, look for corners that stay dark and see how the whole diamond looks under everyday lighting.


• Use a small light source and turn the stone slowly. See where fire appears and when the ends and centre light up.


• Use light and dark backgrounds if you suspect windowing. Check whether the background colour is visible through that area. Camera obstruction, lighting and surface cleanliness can affect the result.


Imagine two face-up stones with dark centres. A small tilt makes the first stone’s centre light up and both ends flash in turn. On the second, the centre stays grey across several angles while the corners do most of the flashing. For the second stone, request another video with changed lighting, background and viewing angles. GIA research on fancy-shape cut and viewing environments


How colour, clarity and setting change the finished appearance


Colourless, yellow and pink cushion diamonds side by side.

Figure 10. Illustrative face-up colour in colourless, yellow and pink cushions.


Where to look for colour and inclusions


Compare colourless to near-colourless stones with similar facet styles in neutral light. Check the centre, ends and corners. Put the centre stone beside any white accents to see whether the corners show a stronger tint. In fancy yellow or fancy pink, check hue, depth of colour and distribution, and how much the colour fades when tilted.


Assess clarity at wearing distance first, then magnify. Two VS2 stones may have very different inclusions: one can be inconspicuous near the edge, while a dark inclusion under the centre of the table can draw the eye. With step cuts, check the broad, open facets. Ask your jeweller to inspect any feather near a thin girdle, corner or planned prong position. GIA advice on protecting diamonds from chipping


What to check in rings, pendants and earrings


For rings, decide on orientation and prong position. Four prongs leave much of the outline visible. A bezel can make a tighter corner feel rounder. For a low setting or a ring stack, compare actual depth with the setting’s side view and check clearance under the culet and against the adjacent band. In a three-stone design, see how much of the centre stone’s corners remain visible.


RAGAZZA cushion three-stone ring, style 600440.

Figure 11. Cushion three-stone ring 600440. The four prongs leave portions of the rounded corners visible, while the side stones extend the design across the finger. View this design


For pendants, check how the bail holds the orientation and whether the pendant tends to flip. For studs, compare millimetre dimensions, corners, hue, profile height and the rhythm of flashes. Two stones with the same length and width can still look mismatched if one throws broad flashes and the other scintillates finely.


RAGAZZA fancy pink cushion halo studs, style 601071.

Figure 12. Fancy pink cushion studs 601071. The image shows the colour and corners of the paired centres, and how the white diamond halos extend the outline. View this design


Frequently asked questions


Why can two 1.25-ratio cushions look so different?


Compare them at equal width. Straighter edges and short corners can resemble a radiant outline. Bowed sides and a continuous curve at the corners retain more of the pillow shape. Overlay the proposed prong or bezel positions on the face-up image to see which portions of that outline will remain visible.


How do I choose between two stones with a 60% table and 66% depth?


Compare crown, pavilion and girdle. A stone with a 12% crown and 50% pavilion can have similar total depth to one with an 8% crown and 54% pavilion. Use video to compare broad flashes, finer scintillation and persistent dark areas, then check the actual dimensions and setting height.


Should I rule out an elongated cushion with a dark band?


Tilt it along both axes in soft light and vary the camera distance. A band that lights up as you move can be normal contrast or camera obstruction. Grey that persists at several angles and reveals the background calls for a closer check for windowing. Watch how both ends return light as well.


How do I verify a crushed-ice look if the report says Cushion Brilliant?


Request face-up and angled loose-stone clips for that report number. At a fixed exposure, check the centre, corners and edges. Dense, fast-changing pinpoints across those areas give the crushed-ice impression. Other stones combine fine edges with broad central flashes.


Is 4.4 mm of report depth enough to assess a low setting or stack?


Check the setting’s side view for clearance below the culet, the girdle’s height relative to the prongs, and where the wedding band meets the basket. Two stones with the same depth can sit at different girdle heights if their crown and pavilion depths differ.


Why do matching carat and colour grades still call for a stud-pair video?


Rotate both stones together in the same lighting. Compare hue, side curves, corner shapes, table orientation and flash patterns. With coloured stones, watch how much each fades when tilted. Turn one 180° to reveal differences between the two ends or between corners.


 
 
bottom of page